On February 28th, 2004, we became the proud parents of a bouncing baby boy. He was born after a relatively short labor, and it only took four pushes to get him out. Despite the fact that he was 3 weeks early, he weighed in at 7 lbs. 10 ozs., and 20.75 inches.

Mother and child are doing just fine. It’s now almost two months later and he is doing great. He’s a much slimmer kid than his sister. In fact, this kid has no tüsh to speak of whatsoever. At his checkup yesterday, his weight is now around the 50th percentile. I don’t recall height, but I belief that he’s around 50 there also.

As for his sister, now that’s another story. She’s right about that age (2) where she’s going to be a handful regardless of now sharing Mom’s attention. Let me put it to you this way, his sister can scream loud enough to set off the glassbreak sensors on the alarm system. Now, that’s some lungs.

At work we are in the process of migrating from a legacy accounting system to Microsoft’s Navision Attain. The legacy app is running on a SCO OpenServer 3.2v2 box. The guy supporting the app wrote a dump utility that creates ASCII files of the data. The trick to get the data from the box.

The box has no NIC. It works completely with serial boards. Do you know how long it takes to cat a 5MB file over a 19.2k serial link? To long to even figure it out. Anyway, I needed to compress the data before I moved it off the box. Um, ok, then WTF do I do with it then? Can’t cat a .tar.Z file. Kermit!

The SCO box has nothing installed for any sort of file transfer (XMODEM, YMODEM, ZMODEM, or Kermit). Fortunately after spending an inordinate amount of time Googling, I found that the folks behind Kermit, Columbia University (in nYc, boyeee!) had a compiled binary for my version of SCO (!). No shit, right? Yes shit!

Ok, so I now have the Kermit binary on my Windows XP box. If you remember the aforementioned problem; no file transfer protocol implementations on the box. Now, how do I get the file to the SCO box? The SCO box has a command, doscp, that allows me to copy a file from a DOS floppy. Therefore, via sneaker net, I marched into the computer room and slipped that 3.5″ floppy from my PC into that bad-boy. Well, long story short, it fuckin’ worked! Oh yeah, pimp status +1. Furthermore, SecureCRT has fair Kermit support. But, um, we have a problem.

The files seemed to be corrupt. Back and forth I went with moving files from the SCO box to my machine. I was able to ruleout any corruption from Kermit because I was able to move raw text files, and an uncompressed tar archive across the link and they worked just fine. Now, WTF is going on? This is where RTFM is actually your friend (yes, you actually heard me say that).

SCO’s compress command is a little left of center when it comes to the standard, or so it seems to gzip. I noticed in the compress man page a -H switch, which changed compress to the use the LZH compression algorithm. Furthermore, the gzip man page says that it works with compress with the -H switch. When I used this switch, gzip’s -d output changed. Acha! We are on the path to ritcheousness. The error that gzip barfed out was “invalid compressed data -- Huffman code > 32 bits“.

Well, back to the compress man page. Compress also takes a -b switch, which allows you to specify the bit size used in compress. By using compress with -H and -b 32, I was able to get a good decompress from gzip. Pimp status +2! You must also provide the -i switch to Kermit, which lets Kermit know that you are transfering a binary file. Othewise, you get sporatic results. Now I am moving the full tar from the box as we speak. It’s over 4 megs so it’ll take close to an hour to move.

Anyway, for posterity, here is the command I used to build my tar:

tar cf - filedump | compress -H -b 32 > filedump.tar.Z

And the Kermit command:

kermit -i -s filedump.tar.Z

In the never ending quest for the ultimate RSS feed reader, I just installed Sage for Firefox. This Firefox extension resides inside the browser and integrates directly with Firefox’s live bookmarks. RSS feeds are displayed in a browser tab. The formatting is based on either an embedded CSS stylesheet, and or an external sheet.

Once installed, Sage requires one change. The default stylesheet does’t handle advanced HTML formatting in the entry all that well. Of course, not too suprising, a Safari like stylesheet has been developed for Sage. The stylesheet resides here at DeviantArt.com. Oh, and to give credit where credit is due, I found about the Safari stylesheet at StarvingArtist.

I was using RssBandit prior. Don’t get me wrong, RssBandit is a fine application, but, it’s another application. There’s just so many apps one man can run. In fact, if it wasn’t for the fact that Thunderbird can’t sync with my BlackBerry, I would migrate off of Outlook. Anyway, enjoy Sage.

Back at Friendly’s again Tonight is the start of a new order. Meg didn’t get peanutbutter cups the other day and wound up with pieces instead. So, she asked for that tonigt. One thing that does is reduce the number of substitutions from 5 to 1. I’m looking forward to a correct order!

I’m at Friendlys and it is quite the trip. For example, the girl who 3 weeks ago couldn’t use the cash register, still can’t. On the bright side, Larry the manager made our sundaes so there’s a far better chance of them being right. Oh, and by the way, why is the price different everytime I come here?

Guess what? I now own a BlackBerry and can blog from the road. This may not mean much, but for someone like me, I can blog from in front of the TV or a boring meeting.
I’m using a MIDLET called MIDlog. It’s written by Daniel Rocha. I appologize for not linking everything, but there’s only so much you can do on a BlackBerry.